When a car sits for months, each tire rests on the same patch of garage concrete — or, if you park outside, in whatever water collects under it. Tire makers and the U.S. tire industry recommend a simple precaution: keep stored tires in a clean, dry place, and raise them off the floor so they are not sitting in moisture. Michelin notes that bare concrete can draw moisture. Yokohama warns that rain and moisture can deteriorate the rubber and rust the steel cord inside the tire.
That is the job of the RVSetRite Auto Storage Kit. Each tire sits on a high-strength 3D-printed tire pad, which keeps the rubber off the concrete and out of standing water.
Why off the concrete, and out of the water
Concrete slabs in a garage or on a driveway can stay damp. Water wicks through the slab and sits at the surface, so a tire left there for a season stays in long, close contact with that moisture.
A common concern is that chemicals in the concrete leach into the rubber and break it down microscopically. The strongest, most consistent guidance from tire makers is about moisture, not a dramatic chemical attack from the slab itself. Modern tires use synthetic rubber blends and protective additives, and they are more resistant than older natural-rubber tires. Even so, official advice has not changed: store tires off the floor, and keep them dry.
Here is what that moisture can do, in plain terms. Prolonged wet contact can slowly affect the rubber at the surface. Protective compounds mixed into the tire — the additives that help the rubber age more slowly — can leach into water over time. If moisture works into the tire, it can reach the steel belts and cords and cause rust. None of this happens overnight, and a pad is not a magic shield. Lifting the tire off the damp slab, or out of a puddle, helps protect the rubber during a long sit.
If the car is parked outside, the same pads lift the tires out of standing water so the rubber is not soaking all winter.
What’s in the Auto Storage Kit
The kit is sold on rvsetrite.com for $89 and includes everything you need for one car — pads and chocks together:
- 4 Auto Tire Protectors (ATP) — one high-strength 3D-printed pad for each tire
- 1 ARCHK rear chock
- 1 AFCHK front chock

The Auto Tire Protectors are the car version of RVSetRite’s Drive-ON pads. They are thinner than the 1-inch RV tire protector (TP1), so they sit lower under a car tire and are a better fit in a garage or storage stall. Like the rest of the RVSetRite line, they are 3D-printed in PETG. The whole kit is lightweight, easy to carry to the parking spot, and easy to pick up when winter is over.
Hold the car without leaving the parking brake set
The red ARCHK goes at the rear of the tire to stop the car. The blue AFCHK goes at the front. Together they hold the car in place while it sits, so you do not need to set or compress the parking brake for the storage season. Leaving a parking brake clamped for months can strain the mechanism or leave it sticky when you come back. The chocks are a simple way to keep the car from rolling without relying on the brake.
Set it down and leave it for the season
Place one Auto Tire Protector under each tire so the tire sits on the high-strength 3D-printed pad, not on the concrete or in standing water. Set the rear chock behind the tire and the front chock in front. Once the car is on the pads and the chocks are in place, you can leave the setup for the storage season.

If you already know RVSetRite from the Drive-ON RV kits, this is the automobile version of that idea — same 3D-printed PETG construction, with thinner pads suited to a car tire. The Auto Storage Kit is available on the RVSetRite website.
Ready to park the car for winter? Shop the Auto Storage Kit on rvsetrite.com. Questions? RVSetRite@gmail.com or 509.879.9699. Ships from Spokane, WA.
Sources
- Michelin, “Storing my tires.” Bare concrete can draw moisture; raise outdoor tires off the ground to limit moisture from below. Michelin Canada; Michelin USA.
- U.S. Tire Manufacturers Association, Tire Information Service Bulletin 23, November 2024. Store tires raised off the surface to minimize moisture; do not store them in a wet area. USTMA TISB 23 (PDF).
- Yokohama, “Tire Storage.” Rain and moisture can deteriorate rubber and rust the steel cord; do not store tires directly on the ground. Yokohama Tire Storage.
- Bridgestone, tire storage FAQ. Store indoors in a cool, dry place; do not let water collect inside the tire. Bridgestone FAQs.
- ISO 2230, Rubber products — Guidelines for storage. Avoid moist conditions and condensation; do not leave rubber in contact with liquids during storage. ISO 2230.

Leave a Reply